AIR200P Air Separator With Dirt Magnet

Home PageAIR200P Air Separator With Dirt Magnet

Rhella AIR200P air and dirt separator with dirt magnet

Air and dirt separator

AIR200P

Air and dirt separator with dirt magnet

The Rhella AIR200P removes entrained air, micro-bubbles, dirt and ferrous particles from closed heating and cooling systems in one 304 stainless steel vessel. Sized for 39 gpm at 4 ft/s, with G2½″ union with 2″ press, sweat or FNPT tail connections.

39 gpmFlow at 4 ft/s G2½″Connections 150 psiMax. pressure 210 °FMax. temperature

3-in-1 performance

1

Air removal

Stainless Pall ring coalescing media merges micro-bubbles so they rise to the automatic air vent.

2

Dirt removal

Slow water in the body lets dirt settle to the bottom for blowdown through the drain.

3

Magnetite removal

A 12,000 gauss neodymium rod in a dry well holds ferrous particles; pull the rod to release them.

4

Easy service

Side fill port for the expansion tank and system fill; the magnet comes out without draining the system.

Dimensions

AIR200P dimensional drawing

Dimensions, mm / in

ABCDE
mm20024085155101
in7.99.43.36.14.0

A Width across the connection faces · B Overall height of the vessel · C Top of vessel to connection centerline · D Connection centerline to bottom of vessel · E Vessel outside diameter. Heights exclude the air vent, drain valve and fittings.

Connections

#PortSize and type
1Inlet and outlet connections (2)G2½″ union with 2″ press, sweat or FNPT tail
2Air vent port½″ FNPT
3Drain½″ GF
4Dirt magnet portdry well with removable rod
5Fill port, on the side (expansion tank or system fill)½″ GF

Technical data

Flow at 4 ft/s39 gpm (9.0 m³/h)
Pressure drop at 4 ft/s0.64 ft (0.28 psi)
Max. operating pressure150 psi (10 bar)
Operating temperature32–210 °F (0–99 °C)
FluidsWater, or water with up to 50 % glycol
VesselØ 101 × 2 mm, 304 stainless steel
Coalescing elementØ16 mm 304 stainless steel Pall rings filling the body between stainless steel mesh screens
Dirt magnetØ16 mm neodymium rod, M50 grade, 12,000 gauss, in a dry well
Weight6.4 lb (2.9 kg)
Water volumeapprox. 0.4 US gal
Warranty2 years

Performance

Pressure drop

AIR200P pressure drop chart

Computed with 3D CFD of the vessel and its internals; pressure drop rises with the square of the flow.

Sizing and installation

Select the separator for the full system flow through it. The listed flow is the flow at 4 ft/s in the connection, a reference point and not a limit: the separator also works at higher flow, with higher pressure drop. At lower flow the water moves more slowly through the body and air and dirt removal improve.

Install vertically with the vent at the top, on the supply side after the boiler or chiller and before the pump suction where possible: there the water is hottest and the pressure lowest, so air comes out of solution most readily.

Maintenance

Open the drain periodically to blow down settled dirt. To release the collected magnetite, pull the rod out of its dry well: the magnetite drops to the bottom and is flushed out at the next blowdown. The automatic air vent needs no routine service.

Typical specification

Furnish and install a Rhella AIR200P air and dirt separator, or approved equal, selected for 39 gpm (4 ft/s connection velocity). The separator shall remove entrained air, micro-bubbles, dirt and ferrous particles in one vessel. The vessel shall be 304 stainless steel with G2½″ union with 2″ press, sweat or FNPT tail inlet and outlet connections, internal Ø16 mm 304 stainless steel Pall rings filling the body between stainless steel mesh screens acting as coalescing medium, an automatic air vent at the top, a ½″ fill port on the side for the expansion tank and system fill, a drain at the bottom, and a removable 12,000 gauss neodymium rod magnet in a dry well. Maximum working pressure 150 psi; working temperature 32–210 °F; suitable for water and glycol solutions up to 50 %.

Flow and performance simulator